V1.0.46(23/08/24)
	New
		Add firmware update support to cloud connected devices
		
	Bugfix
		Exflash raid driver improvements 

V1.0.45(21/05/24) 
	New
		Set all LEDS on EOS at startup
		
	Bugfix
		Invert input alarm state for APDP only, so off = alarm off, on = alarm on

V1.0.44(16/04/24)
	New
		Add cloud buffer when no connectivity
		Add configuration options for event log duplicate suppression and update help with more information
		Update reset source with more detail
		Security and performance improvements
		
V1.0.43(13/02/24) 
	New
		Add customer specific CB value when not present 

V1.0.42(15/01/24) 
	New
		Update TFT alarms screen to display dynamically
		
	Bugfix
		Alarm on non-present APDP core temp 
		Tidy up log-off flow
		APDP factory programming & initialization
		TFT not showing alarms and network when clustering enabled
		Clear orphan alarms if a device is deleted
		Year on data log graphs

V1.0.41(06/12/23) 
	New
		Enable logging of temp monitoring by default
		
	Bugfix
		Cloud enabled devices after reboot send incorrect message length
		TCB ordering for cloud
		Set active bank rather than leaving unknown in flash on first use of a unit
		Crash when no firmware is available in backup bank and revert firmware is used
		Digital input alarm state reporting incorrectly

V1.0.40(04/10/23) 
	Bugfix
		TFT not displaying past 9th cb group

V1.0.39(27/09/23) 
	New
		HWtest minor update
		Add support for APDP FCS with EWS
		
	Bugfix
		Factory serial update js

V1.0.38(18/09/23) 
	New
		Update UI for APDP and IO in groups
	Bugfix
		Local feed e2 driver possible corruption on raid repair

V1.0.37(01/09/23) 
	Bugfix
		APDP voltage calibration initialisation 
		TH probes on DIO and small number of non grouped feeds not displaying summary info

V1.0.36(31/08/23) 
	New
		Update Web UI for sensors pages to group by ews and expansion and provide sensor summaries for Each device when collapsed
		Add all sensors page 

V1.0.35(25/08/23) 
	New
		Update TFT UI
		Remove temp sensors from DIO when not present on PCB
		
	Bugfix
		Fix intermittent sensors not displaying on TFT

V1.0.34(22/08/23)
	New
		feed.cgi interface adjustments, move units to headings and change colours and mouse dropdown on mouseover
		HWTest Updates for new PCB

V1.0.33(27/07/23)
	New
		Add firmware updates for EOS-CT
		Configure alarms and descriptions to follow CT's when order is changed
		Add cloud interface
		Update display to support non grouped feeds

V1.0.32(24/05/23) 
	New
		Add order to feedTable in SNMP
		Rename IPDU-EOS to EOS-LCS
		Add support for EOS-CT
		Add extra warning when adding groups to cabinets - "Expected 6 groups per EOS Cabinet"
		
	Bugfix
		Limit expansion auto recovery frequency per hour

V1.0.31(24/10/22) 
	New
		Update default feed naming convention
		Add one calibration offset for internal use

V1.0.30(04/10/22) 
	Bugfix
		Fix grouping when full count of groups exist

V1.0.29(29/09/22) 
	New
		Remove Group prefix when a description is set. When not set add "Unnamed CB/Fuse Group"
		Provision for customer specific SNTP
		Leave the date set on factory reset
		
	Bugfix
		Resize columns to fit 16th character on TFT

V1.0.28(21/09/22)
	New
		On LCD display, display order if no feed/group description is provided

V1.0.27(13/09/22) 
	New
		Update warning prompt when < 6 groups used
		Add button to auto populate descriptions where needed
		Update Feed to EOS on display where needed

V1.0.26(08/09/22)
	New
		Total power consumption on diags page
			
	Bugfix
		Fix intermittent serial change

V1.0.25(06/09/22)
	New
		Power Log
			
	Bugfix
		Unhide top table in factory use page 

V1.0.24(18/08/22)
	New
		SNMP write
		Heirarchy for 4 or more feeds
		Wildcard domains added to new certificate
		Enable IWDG earlier
		Enable no bootloader firmware
		Added ability to change factory defaults 

V1.0.23(18/05/22)
	New
		Allow concurrent voltage calibration on local feeds
		add support for ACEPDB and vastly increase information on factory page
		add default network control to factory settings
			
	Bugfix
		fix more than 6 DIO's displaying on the factory page

V1.0.22(14/03/22)
	New
		Update data log settings messaging
			
	Bugfix
		Increase timeout of log downloads from 2 mins to 5 mins preventing full logs from finishing 
		Fix error in data log js

V1.0.21(11/03/22)
	Bugfix
		Fix data log frequency not saving until reboot

V1.0.20(02/02/22)
	New
		Configure display to reset on startup if firmware update has not occurred
		Rename from "Multi Const" to "Shunt Amps Per Count" in feed calibration
		Change display backlight to use IOX rather than PWM
		Add node serial print dialogue	
			
	Bugfix
		Fix EWS factory default multi's and offsets skipping the first 8 offsets intermittently
		Fix nominal current constant displaying incorrectly
		Increase reply message length when sending data1 messages

V1.0.19(09/11/21)
	New
		Add extra accuracy to factory page
		Remove center alignment off selects
			
	Bugfix
		Fix power intermittently showing 0 in SNMP 
		Fix display of feed without feed type set

V1.0.18(11/08/21)
	New
		Move EoS cabinet controller outputs from LEDs to Relays
		Add , before cluster

	Bugfix
		Fix last char of serial not displaying for relay outputs

V1.0.17(09/08/21)
	Bugfix
		Fix cabinet controller website display issues
		Fix copy to clipboard used in manufacturing

V1.0.16(02/08/21)
	New
		Improve memory consumption of web server buffers
		Move SNMP memory to TCM
		Configure logoff to move all sessions to the logoff screen
		Order feeds on factory screen 
			
	Bugfix
		Remove decimal place from Feeds with only one cluster in them
		Fix tripped breakers reporting intact on the tft display and current alarms persisting after being disabled until next reboot if tripped breaker is also enabled
		Fix validation on the factory screen
		Fix feed current total on dashboard and tft home page
		Clean extra characters at the end of log exports

V1.0.15(26/07/21)
	New
		Add the ability to disable connection state changes on nodes  
		Move EXP fields not relevant to customer to diags
		In SNMP, configure CB's, fuses, IO's to report as not present if device is disconnected (on top of entire device)
		Add additional diags page for sofware debugging
			
	Bugfix
		Data log frequency changes not applying until next reboot
		Feed detection not assigning letters and speed up process
		Emails dropping last character of the serial
		Duplicate and incorrect connectivity alerts when a EXP device is (dic)connected
		Data log device details getting chopped off
			
V1.0.14(21/07/21)
	New
		Add circuit breaker and fuse status to data log

V1.0.13(19/07/21)
	New
		Remember previous data log filters 
		Allow EoS DIO to be joined to feed
	
	Bugfix
		Fix help page alignment
		Fix data log custom date filters
		EXP manual restart when auto recovery is enabled
		Add hardware change detected to replacing unknown event

V1.0.12(08/07/21)
	New
		Populate feedClusterID in snmp
		Allow feedClusters with more than 2 members and set limit of 8 to number of feedClusters
		MIB version 2.4 which adds connectivity warning traps for EXP devices 
		Update EoS counts per amp coeficcient
		Rename EWS Alarm X to EWS LED Alarm X on output dropdown
		Give comms LED a name under digital IO in the web interface
		Rename identity to feed name and fix full length feed names displaying an extra invalid character
		Move graph cache regen to another thread on cluster change operations
		Refresh screen on feed name change or description change so node heading is properly updated
		Feed current and voltage to factory page
		Copy EWS2 details to clipboard to factory page
		Configure LEDs in web interface for EoS
		Feed I2C addresses on diagnostics page
		Separate exp settings and exp firmware table
		Split firmware file selection and update into steps and add power warning
		Force display refresh parameter and configure for feed changes
		Ordering of feeds
		Dash in serials
		Increase memory to support 24 feeds
		EXP LED alarm, display alarm and dash alarm for disconnected EXP node
		EXP connectivity events, emails and traps
		EXP auto recovery
		EXP firmware retransmit on corrupt packet

	Bugfix
		Fix combination of clustered and unclustered feeds on the dashboard
		Fix feed calculations when feeds contain multiple clusters.
		Hardware revision check on expansion updates
		Fix bug where software version validation is invalid
		EXP device current calculation for data log 

V1.0.11(27/05/21)
	New
		Add support for leds over i2c
		Update SNMP to populate feedCurrentType and optimise message in feedProtXInfo
		Add blank state to tripped breakers when not connected to web interface
		Disable alarms to on EXP devices when not responding 
		Increase device not responding threshold from 3 to 5 seconds
		Add tx of output state to DIO nodes for EoS
			
	Bugfix
		fix default all multis and offsets button not saving persistently
		Fix feedProtectionType in SNMP
		(critical) fix intermittent SMTP crash

V1.0.10(21/05/21)
	New
		Configure applying firmware message to be persistent 
		Add button on support page to reset EWS2 to virgin state
		Rename apdp OLED from Alarm U/NU to LED Alarm U/NU
		Create factory code

V1.0.9(20/05/21)
	New
		Configure alarms on OLED for APDP based on users input
		Adjust APDP for INPUTs and RELAYs not connected

V1.0.8(14/05/21)
	New
		Add input functions to APDP input table in web interface
		Add alarms to OLED for APDP
		Adjust APDPFCS nominal calibration constant for new shunt

V1.0.7(11/05/21)
	New
		Add extra confirmation to apply firmware updates
		add revert firmware option

V1.0.6(10/05/21)
	New
		Increase data log points from 10 to 40
		Relabel CB to CB Current in data log 

V1.0.5(07/05/21)
	New
		Hard code APDP LCS LED and Relays
		Rename ARA to ARA LED and Power to Power LED
			
V1.0.4(07/05/21)
	Bugfix
		Disable ADC AWD
		Fix invalid datalog erases

V1.0.3(07/05/21)
	Bugfix
		Add extra debug information to startup events
		Stop more than 4 firmware retries without a cold boot

V1.0.2(06/05/21)
	Bugfix
		Change IWDG libraries

V1.0.1(06/05/21)
	New
		Rename Urg Relay to U Relay on OLED
		Add codes to startup events

	Bugfix
		Fix intermittent crashes due to graph generation triggering watchdog

V1.0.0(05/05/21)
	New
		Set default voltage calibration points to 55 and 40V
		Add applying firmware to displays
		Set sntp to log after 3 failures rather than 1

	Bugfix
		Set eula to appear for user accounts only
		Fix edge case in crc generator causing malformed firmware
		Fix intermittent crashes due to graph generation triggering watchdog

V0.0.14(03/05/21)
	New
		 Add colours and adjust limits per model of current and power gauges on homepage

	Bugfix
		Fix data log write bug causing sectors to get skipped intermittently 
		Fix energy graphs last data point
		Fix firmware persistence

V0.0.13(30/04/21)
	New
		Add calibration success events
		Change all nominal calibration factors to 1 and introduce per model calibration constants

	Bugfix
		Fix graph errors
		Fix ui bug preventing the saving of LED and RELAY outputs
		Fix feed busbar and core temps in SNMP
		Centre message div on system page
			
V0.0.12(29/04/21)
	New
		

	Bugfix
		Fix voltage calibration for APDP LCS
		Fix energy calculation on dashboard

V0.0.11(28/04/21)
	New
		Initial Release